Category: chiral-nitrogen-ligands

Tris[2-(dimethylamino)ethyl]amine, cas is 33527-91-2, it is a common heterocyclic compound, the chiral-nitrogen-ligands compound, its synthesis route is as follows.,33527-91-2

LiBH4 (22 mg, 1 mmol) and Me6TREN (0.52 mL, 2 mmol) wereadded to 5 mL of THF. This was heated to reflux for 1 h at whichpoint the heat and stirrer were turned off. Slow cooling of the solutionyielded X-ray quality colorless crystals (40 mg, 16%).1H NMR (400.1 MHz, C6D6, 300 K): delta 2.11 (s, 18H, Me6TREN Me),1.94, 1.90 (overlapping br s, 12H, Me6TREN CH2), 0.59 ppm(quartet/septet, 4H, BH4, 1J10BH = 27.5 Hz, 1J11BH = 81.5 Hz).13C NMR (100.6 MHz, C6D6, 300 K): delta 57.0 (CH2), 51.2 (CH2),45.7 ppm (Me).7Li NMR (155.5 MHz, C6D6, 300 K): delta 0.29 ppm.11B NMR (128.3 MHz, C6D6, 300 K): delta 39.5 ppm (quin,1JBH = 81.2 Hz).Elemental analysis for C12H34N4LiB: Calc.: C, 57.15; H, 13.59; N,22.22. Found: C, 57.16; H, 13.48; N, 22.59%.

As the rapid development of chemical substances, we look forward to future research findings about 33527-91-2

Reference£º
Article; Kennedy, Alan R.; McLellan, Ross; McNeil, Greg J.; Mulvey, Robert E.; Robertson, Stuart D.; Polyhedron; vol. 103; (2016); p. 94 – 99;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

(R)-(+)-N,N-Dimethyl-1-ferrocenylethylamine, cas is 31886-58-5, it is a common heterocyclic compound, the chiral-nitrogen-ligands compound, its synthesis route is as follows.,31886-58-5

(S)-Ugi-amine 1 (5.14g, 20mmol) was dissolved in 50mL of diethyl ether. Under nitrogen and ice salt bath cooling, n-butyl lithium (16mL, 2.5mol / L) was added dropwise to the reaction system, After the completion, the temperature was slowly raised to room temperature, and the reaction was stirred for 3 hours. Chlorodiphenylphosphine (8.82 g, 40 mmol) was added dropwise under ice-cooling, and the mixture was slowly warmed to room temperature and stirred for 12 hours. The reaction was quenched with saturated sodium bicarbonate solution. Extracted with dichloromethane, dried over anhydrous sodium sulfate, concentration, column chromatography to obtain compound 2 (5.38g, 61%).

As the rapid development of chemical substances, we look forward to future research findings about 31886-58-5

Reference£º
Patent; Zhejiang University of Technology; Zhong Weihui; Ling Fei; Nian Sanfei; (14 pag.)CN108774271; (2018); A;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

110-70-3, N1,N2-Dimethylethane-1,2-diamine is a chiral-nitrogen-ligands compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,110-70-3

The ligand 345BPMEN was synthesized by modifying thepreviously reported procedure (Singh et al. 2017). To a solutionof 2-chloromethyl-4-methoxy-3,5-dimethylpyridinehydrochloride 2.032 g (9.15 mmol) in 10 mL of water, asolution of potassium carbonate (2.55 g, (18.45 mmol) inwater (10 mL) was added dropwise. After potassium carbonateaddition, very thick white ppts were formed and solutionsolidified. Additional amount of water (50 mL) was addedinto the mixture. After water addition, the reaction mixturewas stirred at room temperature for next 30 min followed bysolvent extraction with dichloromethane (3 ¡Á 20 mL). Thecombined dichloromethane layer was treated with anhydroussodium sulfate. The solution was filtered, and the solventwas removed by rotatory evaporation. The collected light brown oil was dissolved in dichloromethane (10 mL).The above solution was added dropwise to a solution ofN,N?-dimethylethylenediamine 0.493 mL (4.58 mmol) indichloromethane (15 mL). Aqueous solution of 1 M sodiumhydroxide (10 mL) was slowly added and solution wasstirred for additional 60 h at room temperature. After 60 hof stirring was the rapid addition of a second fraction ofaqueous 1 M sodium hydroxide (10 mL, 10 mmol), the productwas extracted with dichloromethane (3 ¡Á 25 mL). Thecombined organic layers were dried over anhydrous sodiumsulfate and filtered. Subsequently, the excess solvent wasevaporated by vacuum to afford brown color viscous oil(1.71 g, Yield 97%). 1H NMR (500 MHz, Methanol-d4) delta8.08 (s, 2H, pyridine ring), 3.76 (s, 6H, -O-CH3-Py), 3.57(s, 4H, -CH2-CH2-Py), 2.56 (s, 4H, -CH2-CH2-), 2.28 (d,6H, CH3-Py), 2.24 (d, 6H, CH3-Py), 2.16 (s, 6H, -N-CH3).ESI-MS+: [345BPMEN + H]+ = 387.32 m/z+ (experimental)387.27 m/z+ (theoretical).

As the paragraph descriping shows that 110-70-3 is playing an increasingly important role.

Reference£º
Article; Botcha, Niharika Krishna; Gutha, Rithvik R.; Sadeghi, Seyed M.; Mukherjee, Anusree; Photosynthesis Research; vol. 143; 2; (2020); p. 143 – 153;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

A common heterocyclic compound, the chiral-nitrogen-ligands compound, name is Tris[2-(dimethylamino)ethyl]amine,cas is 33527-91-2, mainly used in chemical industry, its synthesis route is as follows.

33527-91-2, To a solution of tris[2-(dimethylamino)ethyl]amine (L4)(0.500 g, 2.17 mmol) in MeOH was added Ni(NO3)26H2O(0.0.631 g, 2.17 mmol), followed by stirring at RT for 12 h. A greenprecipitate was obtained after evaporating the reaction solutionand dried. Yield (0.919 g, 98%).

As the rapid development of chemical substances, we look forward to future research findings about 33527-91-2

Reference£º
Article; Sivanesan, Dharmalingam; Seo, Bongkuk; Lim, Choong-Sun; Kim, Hyeon-Gook; Journal of Catalysis; vol. 382; (2020); p. 121 – 128;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

A common heterocyclic compound, the chiral-nitrogen-ligands compound, name is N1,N2-Dimethylethane-1,2-diamine,cas is 110-70-3, mainly used in chemical industry, its synthesis route is as follows.

110-70-3, beta-CD-OTs (500.0 mg, 0.388 mmol) was dissolved in 5 mL dry DMF with 100 mg NaI. N,N?-Dimethylethane-1,2-diamine (1.28 mL, 11.72 mmol) was then added under N2 and the reaction mixture was stirred overnight at 70 C. under N2. The next day the reaction mixture was cooled and precipitated in 50 mL acetone, giving a white precipitate. Unreacted tosylate was removed via the same ion-exchange methods as described above for beta-CD-NH2. Yield=374 mg (80.0%). 1H NMR (300 MHz, D2O, delta): 5.02-4.87 (s, 7H, C1H of CD), 3.93-3.64 (m, 29H, C2H, C3H, C4H, and C5H of CD and NH), 3.61-3.29 (m, 14H, C6H of CD), 3.01-2.36 (m, 10H, N1-CH2, N2-CH2, and N2-(CH3)2).

As the rapid development of chemical substances, we look forward to future research findings about 110-70-3

Reference£º
Patent; Thompson, David H.; Kulkarni, Aditya; Deng, Wei; US2015/202323; (2015); A1;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

A common heterocyclic compound, the chiral-nitrogen-ligands compound, name is Tris[2-(dimethylamino)ethyl]amine,cas is 33527-91-2, mainly used in chemical industry, its synthesis route is as follows.

33527-91-2, General procedure: The copper complex Cu5-1 was dissolved in water, and an excessive amount of an aqueous solution of saturated sodium tetrafluoroborate (manufactured by Wako Pure Chemical Industries, Ltd.) was added while stirring. A precipitated solid was collected by filtering and a copper complex Cu5-72 was obtained.

As the rapid development of chemical substances, we look forward to future research findings about 33527-91-2

Reference£º
Patent; FUJIFILM Corporation; Sasaki, Kouitsu; Kawashima, Takashi; Hitomi, Seiichi; Shiraishi, Yasuharu; US10215898; (2019); B2;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

A common heterocyclic compound, the chiral-nitrogen-ligands compound, name is Tris[2-(dimethylamino)ethyl]amine,cas is 33527-91-2, mainly used in chemical industry, its synthesis route is as follows.,33527-91-2

Mixturing of Co(CH3COO)24H2O (57 mg, 0,23 mmol) and Me6TREN (in excess) was followed by sonication until all the pink cobalt salt was transformed into a bright green oil. The excess of ligand was washed away with diethyl ether.

As the rapid development of chemical substances, we look forward to future research findings about 33527-91-2

Reference£º
Article; Tordin, Elisa; List, Manuela; Monkowius, Uwe; Schindler, Siegfried; Knoer, Guenther; Inorganica Chimica Acta; vol. 402; (2013); p. 90 – 96;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

110-70-3, N1,N2-Dimethylethane-1,2-diamine is a chiral-nitrogen-ligands compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,110-70-3

A mixture of 2-(3-bromo-phenyl)-3,3-dimethyl-1,2,3,4-tetrahydro-quinoline-6-carboxylic acid (600 mg, 1.7 mmol), N,N’-dimethyl-ethane-1,2-diamine (0.37 mL, 3.4 mmol), copper(I) iodide (96 mg, 0.5 mmol), N,N-dimethylglycine hydrochloride (140 mg, 1.0 mmol) and potassium carbonate (923 mg, 6.7 mmol) in dimethyl sulfoxide (5 mL) was stirred at 120 C. for 16 h. Then the reaction mixture cooled to room temperature. The reaction mixture was extracted with ethyl acetate (2¡Á150 mL), washed with water (2¡Á50 mL) and saturated aqueous ammonium chloride solution (2¡Á50 mL), dried over anhydrous sodium sulfate and then concentrated in vacuo. Purification by Waters automated flash system (column: Xterra 30 mm¡Á100 mm, sample manager 2767, pump 2525, detector: ZQ mass and UV 2487, solvent system: acetonitrile and 0.1% ammonium hydroxide in water) afforded 3,3-dimethyl-2-{3-[methyl-(2-methylamino-ethyl)-amino]-phenyl}-1,2,3,4-tetrahydro-quinoline-6-carboxylic acid (500 mg, 80%) as a white solid: LC/MS m/e calcd for C22H29N3O2 (M+H)+: 368.50, observed: 368.1.

The synthetic route of 110-70-3 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Chen, Li; Feng, Lichun; Huang, Mengwei; Liu, Yongfu; Wu, Guolong; Wu, Jim Zhen; Zhou, Mingwei; US2011/257151; (2011); A1;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.110-70-3,N1,N2-Dimethylethane-1,2-diamine,as a common compound, the synthetic route is as follows.,110-70-3

The ligand L1Q was synthesized via similar procedure mentionedabove [23]. To an aqueous solution of 2-(chloromethyl)-quinoline hydrochloride (2 g, 9.34 mmol), a solution of potassiumcarbonate (2.73 g, 18.66 mmol) in 10 mL water was added in dropwisemanner. The reaction mixture was stirred for 30 min at ambienttemperature. After stirring, the resulting solution wasextracted with dichloromethane (3 20 mL). The combinedorganic extracts were dried over anhydrous sodium sulfate andsolvent was evaporates under vacuum. The product 2-(chloromethyl)-quinoline was then dissolved in dichloromethane(10 mL) and was added dropwise to a solution of N,N0-dimethylethylenediamine (0.503 mL, 5.34 mmol) in 15 mL dichloromethane.After this addition, aqueous sodium hydroxide (10 mL,1 M) was added slowly. The reaction mixture was stirred for next60 h at room temperature, followed by rapid addition of anotherfraction of sodium hydroxide (10 mL, 10 mmol). The reaction mixturewas then extracted with dichloromethane (3 25 mL) andorganic portions were combined and dried over anhydrous sodiumsulfate. Volatile solvents were removed under vacuum to obtaincrude ligand L1Q as dark brown oil (1.68 g, Yield 85%). 1H NMR(500 MHz, Methanol-d4) d 7.57 (m, 2H, quinoline ring),7.63 (d,2H, quinoline ring), 7.73 (m, 2H, quinoline ring), 7.88 (d, 2H, quinolinering),7.98 (d, 2H, quinoline ring), 8.21 (d, 2H, quinoline ring),3.84 (s, 4H, -N-CH2-Quinoline), 2.71 (s, 4H, -CH2-CH2-), 2.32 (s,6H, -N-CH3). IR (cm1): 3384, 3056, 2946, 2800, 1617, 1598,1564, 1504, 1456, 1426, 1361, 1309, 1223, 1141, 1119, 1032,985, 951, 828, 784, 756, 619.

The synthetic route of 110-70-3 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Singh, Nirupama; Niklas, Jens; Poluektov, Oleg; Van Heuvelen, Katherine M.; Mukherjee, Anusree; Inorganica Chimica Acta; vol. 455; (2017); p. 221 – 230;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

A common heterocyclic compound, the chiral-nitrogen-ligands compound, name is (R)-(+)-N,N-Dimethyl-1-ferrocenylethylamine,cas is 31886-58-5, mainly used in chemical industry, its synthesis route is as follows.,31886-58-5

Preparation of A1 (mixture of diastereomers)15.5 ml (23.2 mmol) of t-BuLi (1.5 M in pentane) are added dropwise to a solution of 5.98 g (23.2 mmol) of (R)-1-dimethylamino-1-ferrocenylethane in 40 ml of diethyl ether (DE) at <-10C. After stirring the mixture at the same temperature for 10 minutes, the temperature is allowed to rise to room temperature and the mixture is stirred for another 1.5 hours. This gives a solution of the compound X2 which is added via a cannula to a cooled suspension of the monochlorophosphine X1 at such a rate that the temperature does not exceed -30C. After stirring the mixture at -30C for a further 10 minutes, the temperature is allowed to rise to 0C and the mixture is stirred for another 2 hours. The reaction mixture is admixed with 20 ml of water. The organic phase is separated off, dried over sodium sulphate and the solvent is distilled off under reduced pressure on a rotary evaporator. Chromatographic purification (silica gel 60; eluent = heptane/ethyl acetate(EA)/NEthyl3(Net3) 85:10:5) gives 1 1.39 g of the desired product as a mixture of 2 diastereomers. As the rapid development of chemical substances, we look forward to future research findings about 31886-58-5 Reference£º
Patent; SOLVIAS AG; WO2007/116081; (2007); A1;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis